Asymtek DV-7000 Series Скачать руководство пользователя страница 44

Страница: 44 / 60

Troubleshooting

Table 6-1 Troubleshooting Guide

Symptom

Possible Cause

Recovery

Pump poorly primed

See “

Priming the Pump

”

in the

Operation

section.

Clogged needle

Clean or replace the needle

Plugged pump

Clean Pump. See
“

Cleaning the Pump

” in the

Maintenance

and Service

section.

Speed Control set to 0 rpm

See “

Pump Adjustments

” in the

Operation

section.

No power to motor

Make sure that pump power cord is
connected to the power outlet on the
dispensing head.

Intermittent or no fluid
dispensing

Fluid syringe is empty

See “

Installing/Changing a Fluid Syringe

”

in the

Operation

section.

Fluid particles too big for
needle size

Replace needle with a larger diameter
needle.

Needle bent or damaged

Replace needle.

Needle repeatedly
clogs with fluid

Fluid has exceeded pot life
or fill has separated

See “

Installing/Changing a Fluid Syringe

”

in the

Operation

section.

Pump poorly primed

See “

Priming the Pump

”

in the

Operation

section.

Wrong type of stopper in
the syringe

Use zero draft (orange or yellow) stoppers
in the syringe.

Air inside syringe expands

Add a short reverse motor command to the
end of the dispensing command. Refer to
the

Fluidmove User Guide

or Online Help

for instructions.

Material drips or drools
continuously from
dispensing tip

Cartridge preload is
improperly set (DV-8000)

See “

Loading a Dispensing Cartridge

” in

the

Operation

section.

Syringe air pressure set too
low

Increase syringe air pressure (30 psi
max.). Refer to the applicable dispensing
system

Operations Manual

for instructions.

Drive mechanics do not
have time to damp-out after
an X-Y move

Increase the settling time in the Dot
Parameters. Refer to the

Fluidmove User

Guide

or Online Help

for instructions.

Inconsistent shot sizes

Feed screw damaged or
binding

Contact Asymtek Technical Support.

Needle is too big

Replace needle with a smaller needle.

Shots too large

Syringe air pressure set too
high

Decrease syringe air pressure (30 psi
max). Refer to the applicable dispensing
system

Operations Manual

for instructions.

Fluid flow rate too fast
or too slow

Incorrect pump motor
speed

Correct pump motor speed to rate
recommended for the fluid used. Refer to
the applicable dispensing system

Operations Manual

for instructions.

Pump is contacting
other components
during Dispensing
Head movement

Incorrect Valve
Bracket/Mounting Plate
installation

Adjust bracket/plate height. Refer to the

Installation

section.

Содержание DV-7000 Series





























































Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды

Asymtek DV-7000 Series, Руководство пользователя

Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды