Asymtek DV-7000 Series Скачать руководство пользователя страница 40

Страница: 40 / 60

Maintenance and Service

6. Pull the dispensing cartridge out of the pump by gently pulling down on the nozzle.

7. Disconnect the 90-degree elbow fitting from the cartridge fitting.

8. Using a 1/4-inch wrench, unscrew the cartridge fitting from the cartridge.

9. Discard the cartridge fitting in accordance with MSDS recommendations.

10. While holding the cartridge body in one hand and the end of the feedscrew in the other, gently

pull the feedscrew out of the body.

The thrust collar should remain attached to the feedscrew.

11. Using your fingers, remove the lower bearing from inside of the cartridge body.

NOTE

If the cartridge does not have a seal, skip to Step 13.

12. Using a cotton swab, carefully remove the seal from inside of the cartridge body.

The seal is very fragile. If the seal is not damaged, it may be reused.

13. While holding the cartridge body, gently twist the needle retainer to remove it from the end of the

cartridge.

Figure 5-2 DV-8000 Cartridge Disassembly (typical)

14. Use MSDS recommended cleaning solution and a small bottle brush or cotton swab to

thoroughly clean the following parts making sure all fluid and residue is removed:

•

Thrust Collar/Feedscrew

•

Needle

Retainer

•

Lower

Bearing

•

Cartridge

Body

•

Seal (if present)

NOTE

If your DV-8000 is configured with a precision needle, perform Steps 15 through 17. If your
DV-8000 is configured with standard Luer needle, skip to Step 18.

Thrust Collar/
Feedscrew
Assembly

Lower Bearing

Seal (not present in DV-
8442 Series Cartridges)

Cartridge Body

Cartridge Fitting

(Luer)

Needle
(standard Luer)

Needle Retainer

Содержание DV-7000 Series





























































Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды

Asymtek DV-7000 Series, Руководство пользователя

Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды