Asymtek DV-7000 Series Скачать руководство пользователя страница 17

Страница: 17 / 60

Installation

Installation on DispenseMate 550 Series Dispensing Systems

1. Use the Fluidmove software position controls to move the dispensing head to the front center of

the dispensing area.

2. Perform a service shutdown and lock out/tag out power to the dispensing system as specified in

the applicable dispensing system manual.

3. Loosen the six (6) screws on the Z-axis face plate (Figure 3-14A) and slide the face plate up so

that it is flush with the Z-axis extrusion (Figure 3-14B). Tighten the screws on the face plate.

4. Slide the dovetail bracket (included with the valve) into the valve mounting bracket. Secure by

tightening the socket head cap screw on the valve mounting bracket (Figure 3-14C).

5. Make electrical connections as shown in Figure 3-15. The syringe must be installed to connect

the clear fluid line. See "

Installing a Syringe

" in the

Operation

section.

6. Configure the Fluidmove software for the DV-7000/DV-8000 valve. See "

Software

Configuration

" later in this section.

7. After the valve has been installed, you must adjust the Height Sensor Probe. Refer to the

DispenseMate User Guide

NOTES

When using the DV-7000 valve, make sure that the Valve Selector (U27) switch, located

on the main board inside the electronics pan, is set to the proper position. The default
setting is DV-8000. For detailed information, refer to the

DispenseMate User Guide

Figure 3-14 Installing the Valve (DispenseMate)

Figure 3-15 Valve Connections (DispenseMate)

Valve
Mounting
Bracket

Socket Head
Cap Screw

Figure A

Figure B

Figure C

Z-axis Extrusion

Z-axis

Face Plate

Содержание DV-7000 Series





























































Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды

Asymtek DV-7000 Series, Руководство пользователя

Результаты поиска

Содержание DV-7000 Series

Отзывы:

Похожие инструкции для DV-7000 Series

Бренды по названию

Популярные бренды