Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 8

Страница: 8 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions:

Onboard Method

• OPEN SPEED:

Speed at which door opens.

• MAX OPEN FORCE:

Force exerted by motor to open door.

• OPEN START FORCE:

Force exerted by motor at start of

opening cycle to help overcome stack pressure or latch device.

• OPEN STALL FORCE:

Force exerted when door is slowed to

a stop while opening, with 1 being lightest and 10 being

strongest. Measure door force to ensure compliance with

standards and codes.

• ADJUST HOLD OPEN:

Time door is held at open position when

ON/OFF/HO switch is in ON position.

• HOLD OPEN FORCE:

Force exerted to hold door in max open

position. Can be adjusted to overcome stack pressure, wind, or

other forces pushing on door.

• OBST DET SENS:

Amount of time door will push against an

obstruction before stalling or moving in opposite direction.

• OPEN DELAY 1:

Time before door will begin to open once

activation has been received.

Set options.

Using joystick, set options. (Figure 14)

Continue with Input Connections on page 13

Figure 14

Max Open Force

• OPEN DELAY 2:

Time before door will begin to open once

activation has been received. Part of Vestibule functionality.

• PUSH & GO:

As door is manually opened, operator ‘senses’

movement and opens door to full-open position.

• OBSTR DURING CLOSE:

Door will reverse to open position if

it hits an obstruction while closing.

• NO OBSTR NEAR OPEN:

Used with door mounted presence

sensor. Operator will ignore obstruction input from sensor

in last 30 degrees of opening.

• NO OBSTR NEAR CLOSE:

Used with door mounted presence

sensor. Operator will ignore obstruction input from sensor

in last 10 degrees of closing.

• ENERGIZE <20°:

24V outputs will change state when door is

20 degrees from close after a manual or automatic cycle.

• AUDIBLE BEEP:

Turn audible beep feedback from interface

PCB off/on.

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды