Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 7

Страница: 7 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions:

Onboard Method

Adjust opening and closing.

Using joystick, make selections to adjust

electrical opening and closing of door.

(Figure 13)

NOTE: Latch, Sweep, and Backcheck

valves were adjusted during initial

installation so unit functions properly

as a mechanical door closer. See

Installation Instructions for your

model.

Figure 13

Open Speed

6: iiiiii----

Speed/Force and Timing/Location

settings must be adjusted to meet

ANSI BHMA A159.19 (American

National Standard for Power Assist and

Low Energy Power Operated Doors)

requirements for opening and closing
based on door weight

d width. (See

tables below)

Note: To determine minimum times from close to full open, the operator shall be adjusted as shown in the chart. Backcheck occurring at a point

between positions in Table II shall use the lowest setting. For example, if the backcheck occurs at 75 degrees, the full open shall be the time shown in

Table I plus 1.5 seconds.

Doors of other weights and widths can be calculated using the formula:

T = D

/ 133 in US Units

T = D

/ 2260 in SI (metric) Units

Where: T = Time, seconds

D = Door width, inches (mm)

W = Door weight, lbs. (kg)

The values for “T” time have been rounded up to the nearest half secound. These values are based on a kinetic energy of 1.25 lbf-ft.

Table I

Minimum Opening Time to Backcheck or 80 degrees (whichever occurs first) and

Minimum Closing Time from 90 degrees to Latchcheck or 10 degrees (whichever occurs first)

“D” Door Leaf Width

Inches (mm)

“W” Door Weight in Pounds (kg)

100 (45.4)

125 (56.7)

150 (68.0)

175 (79.4)

200 (90.7)

*30 (762)

3.0

3.5

36 (914)

3.0

3.5

4.0

42 (1067)

3.5

4.0

4.5

48 (1219)

4.0

4.5

5.0

5.5

* Check applicable Building Codes for clear width requrements in the Means of Egress. See Appendix for additional door weights.

Table II:

Total Opening Time to 90 Degrees

Backcheck at 60 degrees

Backcheck at 70 degrees

Backcheck at 80 degrees

Table I plus 2 seconds

Table I plus 1.5 seconds

Table I plus 1 second

If the door opens more than 90 degrees, it shall continue at the same rate as backcheck speed. Matrix values are in seconds.

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды