manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Инструкция по программированию

Поделиться
Скачать
Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 26

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

26

6000 Series

 Wiring Diagrams

Electric Latch Retraction Exit Device 

for Smoke Ventilation - Blow Open Function 

(change factory pre-wiring to illustration below - move GND to COM)

•  NOTE: This application must be approved by 

local (AHJ) authority having jurisdiction.

•  Door is normally closed and latched.

•  Fire Alarm activation will retract exit device 

latch bolt and door will automatically open. 

Door will remain open until Fire Alarm 

System has been reset.

•  Door Operator’s main power input must be 

wired into building’s back-up power supply.

•  Exit device allows egress at all times, 

including during power failures. 

•  Activation can be wall switch, card reader, 

key switch, etc (Normally open momentary 

dry contacts).

•  If 3-position switch in Off position and Input 

set to Blow Open, when signal is received from 

Fire Alarm System, door WILL NOT open. If 

3-position switch is On, door will open when 

signal received from Fire Alarm System.

•  If Input is set to Blow Open Override, door 

WILL open when signal is received from Fire 

Alarm System if 3-position switch is in On or 

Off position.

•  To turn on relay (Relay 2), Latch 

Retraction (Output Connections, 

page 14) and/or Open Delay (Set 

options, page 8) features must 

be turned on using adjustment 

procedures on pages indicated.

Содержание Norton 6000 Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды