manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Инструкция по программированию

Поделиться
Скачать
Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 14

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

14

6000 Series

 Programming Instructions

Output Connections (Default)

Use green 2-position connectors on control board to add any necessary 

outputs, such as electric strikes, mag locks, exit devices, door open 

position output, etc. (Figure 20) 

 

NOTE: Relay outputs can be customized.

  

 

Relay Outputs

The operator has two relay outputs which may be wired to external 

control systems or devices. The function of each relay is selectable 

depending on the needs of the installation.

The outputs are labeled RLY 1 and RLY 2 like the wiring terminal blocks on 

the operator hardware.

Click Restore Defaults to set the input and output functions to factory 

default, if needed. Be sure to click Save after making changes.

These are the relay output functions:

3 Second Relay

Normally open relay that closes for 3 seconds after an activation to open.

Open POS Relay

Normally open relay that closes when door is in open position.

Closed POS Relay

Normally open relay that closes when the door is in the closed position.

Door Latch Relay

Normally open relay that closes any time the door is not in the closed 

position.

Figure 20 

Output 

Connectors

Содержание Norton 6000 Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды