Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 32

Страница: 32 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series

Wiring Diagrams

596 Presence Detector on Single Door Opening

(change factory pre-wiring to illustration below - move NO to +24)

596 Presence Sensor

mounted to opening side

or closing side of door

(on single opening)

• Door is normally closed.

• Activating switch will open door.

• Door will close after hold open time delay has elapsed.

• If using door mounted presence sensors:

For Closing Cycle sensor (SS1) Input 4 to be set to Obstruction 1

For Opening Cycle sensor (SS2) Input 3 to be set to Obstruction 2

Alternate 24V

Source (+V and

-V of Power

Supply)

NOTE: For Low Energy Operators, Presence

Detectors and/or sensors CANNOT be used

to activate an opening cycle of the door.

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды