Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 15

Страница: 15 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series

Programming Instructions

Status Definitions

Technical support may request status information during a consultation.

Serial Number:

Each operator has a unique serial number listed on the App

Help screen and also located inside 3 Position switch door (see Figure 14,

page 7).

Firmware Version:

This is the version of the control program in the

operator.

Hardware Version:

This is the version of the electronic hardware in the

operator.

System Errors:

Any errors detected by the operator are listed on the App

Help screen and Support page with troubleshooting suggestions.

Cycle Count:

This is the number of door open/close cycles that the operator

has performed in its life.

Door Open Time:

This is the time it took the door to move from closed

to full open position on the last open/close cycle, not including any

programmed opening delay. This information is useful when adjusting door

speed to comply with code.

Door Close Time:

This is the time it took the door to move from full open

position to closed on the last open/close cycle. This information is useful

when adjusting door speed to comply with code.

Door Position:

This is the current angular door position in degrees,

with the closed position being zero degrees.

Double Door Status:

If the operator is configured for double door

operation, the serial number of the connected door appears here.

24V Power Status:

This is the voltage of the 24V DC power source

for the operator.

HV Power Status:

This is the voltage of the high voltage DC power

source of the operator which runs the motor.

Drive Temperature:

The motor driver temperature is shown here. If

the operator has not been in use, this temperature should be near

ambient temperature (perhaps higher or lower due to exterior heat

or cold). The motor driver heats as the operator is used, and the

operator monitors this temperature continuously.

Relay 1:

This is the state of relay number 1, on or off. The relays may

be programmed for various types of operation as the door opens

and closes. See the Connections page.

Relay 2:

This is the state of relay number 2, on or off. The relays

maybe programmed for various types of operation as the door

opens and closes. See the Connections page.

24V N.O. Output:

This is the state of the 24V normally open output,

on or off. The normally closed output is always in the opposite state.

Error Codes for RED POWER LED Flashes

Number

of Flashes Error

Description

Solution

Configured Settings Error

Configured settings have been lost.

Try restoring factory settings to see if that clears the problem. Set up the

operator as needed.

24VDC Power Error

Operator 24V power supply is

malfunctioning or there is a wiring problem.

Make sure all connections are tight. Use a voltmeter to measure power

supply output voltage bV and -V screw terminals. Voltage

should be between 23.7V and 24.3V DC with door closed or opening.

Learn Error

Learn process failed, perhaps due to

an obstruction, faulty hinges, or other

mechanical issue.

Be sure door is in good mechanical working order and retry learn

operation.

Motor Error

There is a problem with main motor.

Check all wiring and gently set all connectors on operator, with power

off. Power up operator and check operation.

Over Temperature Error

Motor has overheated.

Close door for 15 minutes and check that error subsides as motor cools.

Power Board Error

Power board is not plugged in.

Turn power off and wait 5 minutes. Check that circuit boards in

operator are all fastened securely and plugged together per installation

instructions.

Temperature Probe Error

Motor temperature probe is disconnected

or damaged.

Check all wiring and gently set all connectors on operator, with the

power off. Power up operator and check operation.

Sensors Error

Position sensors governing operator are not

working correctly.

Turn off and wait 5 minutes. Check that circuit boards in operator are all

fastened securely and plugged together per installation instructions.

Motor Duration Error

Motor ran longer than allowed.

On/Off switch may be toggled to clear this error or operator may be

restarted.

Double Door Error

Cable connecting the two doors is

disconnected or damaged.

If this is only a single door, be sure it is set as a single door. If this is a door

in a double door pair, be sure sync cable between doors is connected

securely.

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды