Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 31

Страница: 31 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series

Wiring Diagrams

585 Presence Detector

mounted to / above frame

(on single opening)

585 Presence Detector on Single Door Opening

• Door is normally closed.

• Activating switch will open door.

• Door will close after hold open time delay has elapsed.

• If door is closed and 585 Presence Detector senses

something in the opening, door will not open when

activated.

• If door is at open position and 585 Presence Detector

senses something in the opening, door will not close

after hold open time delay has elapsed.

• Once opening is clear, door will close after hold open

time delay has elapsed again.

NOTE: For Low Energy Operators, Presence Detectors and/

or sensors CANNOT be used to activate an opening cycle of

the door.

To activate presence detector functionality:

• Use instructions provided with 585 sensor to program

and make any necessary adjustments to sensor.

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды