Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 6

Страница: 6 / 34

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions:

Onboard Method

Set door open and door closed positions.

1. To set closed position, fully close door. Press and

release CLOSE button on board. Flashing ORANGE

LED should turn solid. (Figure 10)

NOTE: Any time door is in closed position, orange

LED should be solid.

GREEN OPEN LED should now be flashing.

3. To set the fully open position, manually open door to

open position and hold door there.

NOTE: If there is a wall or door stop at open

position, hold door slightly away from wall or stop.

4. Press and release OPEN button on board. Flashing

GREEN OPEN LED should turn solid. Let door close.

(Figure 11)

NOTE: Any time door is in open position, green LED

should be solid.

NOTE: If open position is not set within 30 seconds

of setting closed position, closed position must set

again.

NOTE: Once door has fully closed, make sure there

are no obstructions that could prevent door from

opening. Latching hardware must not prevent

door from opening during following step.

5. Operator must now learn its internal settings. Press

and release LEARN button on board. BLUE LEARN

LED will start flashing and door will open in small

increments. Allow door to open and close without

interference. (Figure 12)

NOTE: After operator has learned settings, if spring

is adjusted or accessories are attached to door that

would make door heavier, operator MUST relearn

internal settings by repeating step 5.

6. Once setup is complete, use Open Pos Adjust setting

to gain up to an additional 5 degrees of opening.

Figure 10

Open Door and

Push OPEN Button

Close Door and

Push CLOSE Button

Close Door and

Push LEARN Button

Figure 11

Figure 12

Содержание Norton 6000 Series



































Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды

Assa Abloy Norton 6000 Series, Инструкция по программированию

Результаты поиска

Содержание Norton 6000 Series

Отзывы:

Бренды по названию

Популярные бренды