manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Инструкция по программированию

Поделиться
Скачать
Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 25

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

25

6000 Series

 Wiring Diagrams

Electric Latch Retraction Exit Device Powered Through 782N Controller

(change factory pre-wiring to illustration below - move GND to COM)

•  Door is normally closed and latched.

•  Activating switch will retract exit device 

latch bolt and door will automatically 

open. Door will close after hold open 

time delay has elapsed.

•  Exit device allows egress at all times, 

including during power failures. 

•  Activation can be wall switch, card 

reader, key switch, etc (Normally open 

momentary dry contacts).

•  Contact Tech Support for other devices 

or manufacturer’s instructions.

•  To turn on relay (Relay 2), Latch 

Retraction (Output Connections, page 

14) and/or Open Delay (Set options, 

page 8) features must be turned on 

using adjustment procedures on pages 

indicated.

Содержание Norton 6000 Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды