manualshive.com logo in svg

Assa Abloy Norton 6000 Series, Инструкция по программированию

Поделиться
Скачать
Assa Abloy Norton 6000 Series Скачать руководство пользователя страница 23

80-9360-1043-020  Rev 1  05/21

Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

23

6000 Series

 Wiring Diagrams

Electric Dogging Exit Device

(change factory pre-wiring to illustration below - move NO to +24)

•  Door is normally closed and latched.

•  Turning key switch ON will apply power to exit device.

•  First depression on device touch bar will electrically 

dog device for push/pull operation. Door will now open 

automatically when wall switch is depressed. Door will 

close after hold open time delay has expired.

•  Device will re-latch during a power failure or when key 

switch is turned off.

•  Exit device allows egress at all times, including during 

power failures. 

•  Activation can be wall switch, card reader, key switch, etc 

(Normally open momentary dry contacts).

•  Current draw at Power Outputs not to exceed 1.3A.

•  To turn on relay (Relay 2), Latch Retraction (Output 

Connections, page 14) and/or Open Delay (Set options, 

page 8) features must be turned on using adjustment 

procedures on pages indicated.

Содержание Norton 6000 Series



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды