Ashley DVAG11L Скачать руководство пользователя

Страница: 4 / 44

REQUIREMENTS FOR THE

COMMONWEALTH OF

MASSACHUSETTS

The following requirements reference various

Massachusetts and national codes not contained

in this manual. For all sidewall horizontally vented

gas fueled equipment installed in every dwelling,

building or structure used in whole or in part for

residential purposes, including those owned or

operated by the Commonwealth and where the

side wall exhaust vent termination is less than (7)

feet above finished grade in the area of the venting,

including but not limited to decks and porches, the

following requirements shall be satisfied:

INSTALLATION OF CARBON MONOXIDE

DETECTORS

At time of installation of side wall horizontally vented

gas fueled equipment, the installing plumber or

gas-fitter shall observe that a hard wired carbon

monoxide detector with an alarm and battery

back-up is installed on the floor level where the

gas equipment is to be installed. In addition, the

installing plumber or gas-fitter shall observe that

a battery operated or hard wired carbon monoxide

detector is installed on each additional level of the

dwelling, building or structure served by the side

wall horizontal vented gas fueled equipment. It shall

be the responsibility of the property owner to secure

the services of qualified licensed professionals for

the installation of hard wired carbon monoxide

detectors. In the event that the side wall horizontally

vented gas fueled equipment is installed in a crawl

space or attic, the hard wired carbon monoxide

detector with alarm and battery back-up may be

installed on the next adjacent floor level. In the

event that the requirements of this subdivision can

not be met at the time of completion of installation,

the owner shall have a period of thirty (30) days to

comply with the above requirements; provided,

however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with

an alarm shall be installed.

APPROVED CARBON MONOXIDE

DETECTORS

Each carbon monoxide detector as required in

accordance with the above provisions shall comply

with NFPA 720 and be ANSI/UL 2034 listed and IAS

certified.

SIGNAGE

A metal or plastic identification plate shall be

permanently mounted to the exterior of the

building at a minimum of eight (8) feet above

grade directly in line with the exhaust vent terminal

for the horizontally vented gas fueled heating the

appliance or equipment. The sign shall read, in

print no less the one-half inch (1/2”) in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS”.

INSPECTION

The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not

approve the installation unless, upon inspection, the

inspector observes carbon monoxide detectors and

signage installed in accordance with the provisions

of 248 CMR 5.08 (2) (a) 1 through 4.

EXEMPTIONS

The following equipment is exempt from 248 CMR

5.08 (2) (a) 1 through 4: The equipment listed in

Chapter 10 entitled “Equipment Not Required To

Be Vented” in the most current edition of NFPA 54

as adopted by the Board; and Product Approved

side wall horizontally vented gas fueled equipment

installed in a room or structure separate from the

dwelling, building or structure used in whole or in

part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided: When

the manufacturer of Product Approved side wall

horizontally vented gas equipment provides

a venting system design or venting system

components with the equipment, the instructions

provided by the manufacturer for installation of the

equipment and the venting system shall include:
Detailed instructions for the installation of the

venting system design or the venting system

components; and a complete parts list for the

venting system design or venting system.

GAS EQUIPMENT VENTING SYSTEM NOT

PROVIDED

When the manufacturer of Product Approved side

wall horizontally vented gas equipment does not

provide the parts for venting the flue gases, but

identifies “special venting systems”, the following

requirements shall be satisfied by the manufacturer:

MASSACHUSETTS RESIDENTS

Содержание DVAG11L













































Результаты поиска

Содержание DVAG11L

Отзывы:

Похожие инструкции для DVAG11L

Бренды по названию

Популярные бренды

Ashley DVAG11L, Инструкция и руководство по эксплуатации для владельца

Результаты поиска

Содержание DVAG11L

Отзывы:

Похожие инструкции для DVAG11L

Бренды по названию

Популярные бренды