Ashley Ashley AP5660, Инструкция по установке и эксплуатации

Страница: 19 / 36

Operation
• DO NOT USE CHEMICALS OR FLUIDS TO START
THE FIRE - Never use gasoline, gasoline-type
lantern fuel, kerosene, charcoal lighter fluid, or
similar liquids to start or “freshen up” a
fi re in this
stove. Keep all such liquids well away from the
stove while it is in use.
• HOT WHILE IN OPERATION. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY. CONTACT MAY
CAUSE SKIN BURNS.
This heater is designed to burn only PFI Premium grade
pellets. This appliance can also burn pellets rated as standard
after May 16, 2015
1. Garbage;
2. Lawn clippings or yard waste;
3. Materials containing rubber, including tires;
4. Materials containing plastic;
5. Waste petroleum products, paints or paint thinners, or
asphalt products;
6. Materials containing asbestos;
7. Construction or demolition debris;
8. Railroad ties or pressure-treated wood;
9. Manure or animal remains;
10. Salt water driftwood or other previously salt water
saturated materials;
11. Unseasoned wood; or
12. Paper products, cardboard, plywood, or particleboard.
The prohibition against burning these materials does
not prohibit the use of
fi re starters made from paper,
cardboard, saw dust, wax and similar substances for
the purpose of starting a
fi re in an affected wood heater.
DO NOT BURN:
Burning these materials may result in release of toxic fumes
or render the heater ineffective and cause smoke.
PROPER FUEL
THIS STOVE IS APPROVED FOR BURNING PELLETIZED
WOOD FUEL ONLY! Factory-approved pellets are those 1/4”
or 5/16” in diameter and not over 1” long. Longer or thicker
pellets sometimes bridge the auger
fl ights, which prevents
proper pellet feed. Burning wood in forms other than pellets
is not permitted. It will violate the building codes for which
the stove has been approved and will void all warranties. The
design incorporates automatic feed of the pellet fuel into the
fi re at a carefully prescribed rate. Any additional fuel introduced
by hand will not increase heat output but may seriously impair
the stoves performance by generating considerable smoke.
Do not burn wet pellets. The stove’s performance depends
heavily on the quality of your pellet fuel. Avoid pellet brands
that display these characteristics:
Excess Fines – “Fines” is a term describing crushed pellets
or loose material that looks like sawdust or sand. Pellets can
be screened before being placed in hopper to remove most
fi nes.
Binders – Some pellets are produced with materials to hold
the together, or “bind” them.
High ash content – Poor quality pellets will often create
smoke and dirty glass. They will create a need for more
frequent maintenance. You will have to empty the burn pot
plus vacuum the entire system more often. Poor quality pellets
could damage the auger. We cannot accept responsibility for
damage due to poor quality pellet.
PRE-START-UP CHECK
Remove burn pot, making sure it is clean and none of the
air holes are plugged. Clean the fi rebox, and then reinstall
burn pot. Clean door glass if necessary (a dry cloth or paper
towel is usually suf
fi cient). Never use abrasive cleaners on the
glass or door. Check fuel in the hopper, and re fi ll if necessary.
BUILDING A FIRE
Never use a grate or other means of supporting the fuel.
Use only the burn pot supplied with this heater.
Hopper lid must be closed in order for the unit to feed pellets.
During the start-up period:
1. Make sure burn pot is free of pellets.
2. DO NOT open the viewing door.
3. DO NOT open the damper, the damper needs to be
closed during start up.
4. DO NOT add pellets to the burn pot by hand.
NOTE: During the
fi rst few fi res, your stove will emit an odor
as the high temperature paint cures or becomes seasoned to
the metal. Maintaining smaller
fi res will minimize this. Avoid
placing items on stove top during this period because paint
could be affected.
Attempts to achieve heat output rates that exceed heater
design speci fi cations can result in permanent damage to the
heater.
THE HOTROD AUTOMATIC FIRESTARTER
Fill hopper and clean burn pot.
Press “On/Off” button. Make sure green light comes on.
The damper should be completely closed or open no more
than ¼ of the way during start-up. This will vary depending on
your installation and elevation. Once
fi re is established adjust
for desired fl ame increasing the amount the damper is open
as the heat setting is increased. (See “DAMPER CONTROL”)
Adjust feed rate to desired setting by pressing “Heat Level
Advance” button.
If fi re doesn’t start in 12 minutes, press “On/Off”, wait a few
minutes, clear the burn pot, and start procedure again.
DAMPER CONTROL
The damper control lever is located on the back of the
stove on the lower left side. The dampener adjusts the
combustion air. This control is necessary due to the varied
burn characteristics of individual installations, different pellet
brands and pellet feed rates. It allows you to improve the
19