ASCOM ELISE2 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 32

ASCOM ELISE2 Скачать руководство пользователя страница 11

TD 92232GB

2005-06-15 / Ver.G

Installation Guide
ELISE2

9

Note:

Only install one ELISE2 module at a time, otherwise problems might occur during IP

addressing.

Installation Procedure

1

Read chapters 4.1 and 4.2 before starting the installation.

2

At delivery ELISE2 is configured for system communication on the A-bus. If modular
system bus cabling is used and the B-bus shall be used for system communication,
follow the instructions in

4.3 Selection of A or B-bus

3

At delivery, the ELISE2 is configured to be connected to a Central Unit on the A/B-
bus. If the ELISE2 should control the communication on the A/B-bus, follow
instructions in

ELISE2 controlling the Communication on the A/B-bus

4

Mount ELISE2 on the wall, follow instructions in

and

4.6 Mounting Together with Other Units

.

5

Set the system bus address, follow instructions in

4.7 System 900 Addressing

6

Connect the system bus, follow instructions in

4.8 Connection of System Bus

and

4.9 Connection of Supply Voltage

7

Optionally connect outputs and inputs described in

4.10 Additional Connections

8

Activate the battery, follow instructions in

4.11 Activation of Battery

9

Perform a network parameter setup of ELISE2, follow instructions in

4.12 Setup of

Network Parameters

10

Connect Ethernet connector to the Local Area Network, follow instructions in

Connection of Ethernet

11

Perform a test of the installation, follow the instructions in

4.14 Installation Test

12

Continue with additional parameter setup for the unit according to chapter

and respective software application documentation.

13

Make a backup copy of all parameters.

4.1

Opening the Housing

Use a screwdriver or similar to release the cover by applying a light pressure to the two
snap catches (1) and remove the cover (2).

Figure 5. Opening the ELISE2 housing.

1

1

2

006

«
...
9
10
11
12
13
...
»

Содержание ELISE2

































Отзывы:

Нет отзывов