manualshive.com logo in svg

ASCOM ELISE2, Руководство по установке, Страница: 2 / 32

Поделиться
Скачать
ASCOM ELISE2 Скачать руководство пользователя страница 2

TD 92232GB

2005-06-15 / Ver.G

Installation Guide
ELISE2

Contents

1 Introduction.............................................................................................................  1

2 Board Description....................................................................................................  2

3 General Information ...............................................................................................  4

3.1 Licence  .............................................................................................................. 4

3.2 Power Down and Restart of ELISE2  .................................................................... 4

3.3 Operating Modes ............................................................................................... 4

3.4 Selection of Operating Mode  ............................................................................. 5

3.5 Function Indicator  .............................................................................................. 6

3.6 Administration and Authentication  .................................................................... 7

4 Installation...............................................................................................................  8

4.1 Opening the Housing ......................................................................................... 9

4.2 Wiring Runs  ..................................................................................................... 10

4.3 Selection of A or B-bus  .................................................................................... 11

4.4 ELISE2 controlling the Communication on the A/B-bus  ..................................... 11

4.5 Mounting  ........................................................................................................ 13

4.6 Mounting Together with Other Units ................................................................ 13

4.7 System 900 Addressing  .................................................................................... 14

4.8 Connection of System Bus  ............................................................................... 14

4.9 Connection of Supply Voltage .......................................................................... 16

4.10 Additional Connections .................................................................................. 17

4.11  Activation of Battery  ..................................................................................... 19

4.12 Setup of Network Parameters  ........................................................................ 20

4.13 Connection of Ethernet .................................................................................. 22

4.14 Installation Test Procedure  .............................................................................. 22

4.15 Clock Synchronisation and Time Settings  ....................................................... 23

4.16 Message Distribution  ..................................................................................... 24

4.17 Unite Name Server (UNS)  ............................................................................... 25

5 Maintenance Information.....................................................................................  25

5.1 Replacement of the Compact Flash  .................................................................. 25

5.2 Updating Application Software  ........................................................................ 25

5.3 Replacing an Image on the Compact Flash  ....................................................... 26

5.4 Installing an Image on an empty Compact Flash  ............................................... 26

5.5 Updating the Software Licence  ........................................................................ 26

5.6 Circuit Board Replacement  ............................................................................... 27

Appendix A: LON Piggy Back Circuit Board (LPB) ..................................................  28

Содержание ELISE2

































Отзывы:

Нет отзывов