ASCOM ELISE2 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 32

ASCOM ELISE2 Скачать руководство пользователя страница 6

TD 92232GB

2005-06-15 / Ver.G

Installation Guide
ELISE2

4

3

General Information

3.1

Licence

All ELISE2 units must have a valid software licence.

The licence can be found on the administration web page, under the section System
Setup > Common > Licence.

IMPORTANT:

Changing this field may seriously affect the functionality.

If no valid licence is present, the unit will not start and the Function Indicator (see

will indicate licence error with a slow flashing red light. The unit can be started in
unlicensed mode, see

Unlicensed Mode

Selection of Operating Mode

on page 5 for more information. Unlicensed mode is indicated by the Function Indicator
with an orange light (3000 ms ON/100 ms OFF), see also

3.5 Function Indicator

3.2

Power Down and Restart of ELISE2

Power Down

1

Remove the cover from the ELISE2 module.

2

Press the push button SW4 to perform a shut down of the processor.

3

Wait until the Function Indicator is flashing orange.

4

Remove the power cable. The power must be removed within 10 minutes or ELISE2
will restart. If ELISE2 restarts, wait until the Function Indicator is not indicating
starting up (flashing orange) before pressing SW4 again.

Restart

There are two ways to restart an ELISE2; following the instruction above and then
replacing the power cable or initiate a restart from the administration web page.

3.3

Operating Modes

There are five different operating modes; normal, network setup, fail-safe, image
installation and unlicensed.

Network Setup Mode

To be able to contact the ELISE2, a valid and unique IP address is necessary. In this mode,
the IP address is set to 192.5.36.229, which is reserved for installation of ELISE2. Network
Setup Mode should only be used when ELISE2 has not got any IP address or when the IP
address has to be changed, i.e. if ELISE2 has been moved from one network to another.

Fail-safe Mode

This mode can be used when it is impossible to contact the ELISE2. When started in Fail-
safe Mode, no applications are started. It is possible to return to factory settings or a
backup copy of parameters from the web page xxx.xxx.xxx.xxx/admin (xxx.xxx.xxx.xxx is
the IP address given to the ELISE2). If there is a problem accessing this page, it is possible
to access xxx.xxx.xxx.xxx/system, where it is possible to change network parameters or
install new software.

«
...
4
5
6
7
8
...
»

Содержание ELISE2

































Отзывы:

Нет отзывов