ASCOM ELISE2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

ASCOM ELISE2 Скачать руководство пользователя страница 7

TD 92232GB

2005-06-15 / Ver.G

Installation Guide
ELISE2

5

Image Installation Mode

The Compact Flash includes the ELISE2 operating system and application software. If all
information (operating system and application software) needs to be updated, then the
complete Compact Flash image must to be replaced. The ELISE2 is normally set in image
installation mode from the administration pages but it can also be set by the operating
mode switch. See

Replacing an Image on the Compact Flash

Installing an Image on an empty Compact Flash

If the Compact Flash needs to be partly updated with new application software, the image
installation mode should

not

be used. For more information, see

Updating Application

Unlicensed Mode

It is possible to run the ELISE2, with limited functionality, without a licence. How the mode
functions is application dependent. For more exact information about the functionality
during unlicensed mode, see the application documentation.

In unlicensed mode, it is possible to enter a licence that does not match the current
hardware. This makes it possible to configure a Compact Flash on one hardware and move
the Compact Flash to another hardware without changing the licence.

3.4

Selection of Operating Mode

All 8 sections of SW3 are set to OFF for normal operating mode.

Figure 3. Switch for selection of operating mode.

Changing Operating Mode

1

Set the section that corresponds to the operating mode to ON.

2

Open the administration web page and press "Reboot" or follow the instructions in

Power Down and Restart of ELISE2

Section 1:

Network setup mode

Section 2:

Fail-safe mode

Section 3:

Not used, must be set to OFF

Section 4:

Image Installation mode

Section 5:

Unlicensed mode

Section 6:

Not used, must be set to OFF

Section 7:

Not used, must be set to OFF

Section 8:

Not used, must be set to OFF

1

OFF ON

8

SW3

003

«
...
5
6
7
8
9
...
»

Содержание ELISE2

































Отзывы:

Нет отзывов