AS DH -N2 Series Скачать руководство пользователя | Manualshive

Страница: 31 / 44

background image

EN

AS Strömungstechnik GmbH

www.asstroemungstechnik.de

Version date: 09/2020

31

2. Open the tamper-proof cap and

remove the red seal. Place both, if

available, in the docking station on the

system side (see Section 3.1).

WARNING

Inhalation of chemical gases!

Inhalation of chemical gases is a health

hazard.
• Open the container only while the

chemical gas is being extracted.

• Please observe the applicable thresh-

old limit values.

• Wear the necessary personal pro-

tective equipment (PPE) (suitable

protective clothing, protective gloves,

respirators and safety goggles / face

shield).

Assembly/commissioning

3. Slowly open the dip tube closure (2)

with the bung wrench (3) in case the

contents are under pressure. (See

Section 3.1)

»

If the container is under pressure

when opened, it is drained via the ven-

tilation holes in the dip tube. You may

hear a hissing sound. In this case, do

not open the dip tube closure any fur-

ther, but wait until no more hissing can

be heard.

»

Check whether a bung wrench with

a special chamber for neutralization

granulate can be used so that the

escaping gases can be additionally

neutralized when opening.

»

If the chemical escapes when the

container is opened, the container has

been overfilled by the chemical filler.

If this is the case, close the container

again immediately and contact the

chemical filler / manufacturer / sup-

plier.

«
...
29
30
31
32
33
...
»

Содержание DH -N2 Series













































Отзывы:

Нет отзывов

Похожие инструкции для DH -N2 Series

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Ecco Страницы: 3

Бренд: Panasonic Страницы: 174

Бренд: FEAS Страницы: 72

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Бренд: T&D Страницы: 28

Бренд: VADDIO Страницы: 58

Бренд: Mako Страницы: 17

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 12

Бренд: L-Acoustics Страницы: 5

Бренд: NAMYSLO Страницы: 13

Бренд: Toro Страницы: 4

Бренд: York International Страницы: 16

Бренд: X-10 Страницы: 12

Бренд: Equinox Systems Страницы: 8

Бренд: Poulan Pro Страницы: 17

KONTROL KUBE ABACUS

Бренд: FIBERLOCK Страницы: 8

Бренд: Gronomics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды