AS DH -N2 Series Скачать руководство пользователя

Страница: 26 / 44

AS Strömungstechnik GmbH

www.asstroemungstechnik.de

Version date: 09/2020

3. Connect the ventilation line to the vent

port of the fill head.

CAUTION

Danger due to leaks!

Exceeding the maximum permissible

pressure can lead to leakage.
• Take suitable protective measures

against exceeding the maximum per-

missible pressure. Please also note

the specifications of the container

manufacturer.

The vent port is used only to connect

a ventilation line. Never use it as a

return flow for liquids.

With fill heads, the vent port is used to

relief pressure build up inside the con-

tainer while filling.

4. Check whether the container can be

inerted with nitrogen before the filling

process.

In the case of fill heads with a second

gas connection, nitrogen can be

introduced through this second con-

nection. The excess nitrogen in the

container escapes through the vent

connection.

If inerting is carried out in combination

with a long dip tube in empty contai-

ners, the nitrogen cushion builds up

from the bottom in the container.

In recirculation applications, in which

a dispense head and a fill head are

attached to the container, the standard

ventilation connections can be used to

inert the container with nitrogen before

operation.

Assembly/commissioning

5. Mount the fill head on a empty contai-

ner or for recirculation applications in

combination with a dispense head on

a container filled with ultra pure water.

For assembly, see the section „Moun-

ting the fill head“.

6. Perform a test run with ultra pure wa-

ter and check the following points:
•

Tightness of the connections and

interfaces,

•

Closing behavior of the valves;

the valves (check valve, plug

valve (turncock) or ball valve)

must seal completely,

•

Ventilation of the container at

maximum flow rate.
If no pressure range is available/
measurable, visually check that
the flow rate is constant and that
the container does not inflate or
collapse.

A fill head with a manual shut-off valve

can be used for pressureless filling.

CAUTION

Danger due to leaks!

Exceeding the maximum flow rate can

lead to leakage.
• Take suitable protective measures

against exceeding the maximum flow

rate.

Содержание DH -N2 Series













































Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды

AS DH -N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды