AS DH -N2 Series Скачать руководство пользователя страница 7

Страница: 7 / 44

AS Strömungstechnik GmbH

www.asstroemungstechnik.de

Version date: 09/2020

JNIOSH-TR-No.42 2007 (Japan),

NFPA Recommended Practice on

Static Electricity (USA). It must also be

checked whether a correspondingly

long dip tube can be used for the re-

turn / filling into the container, which

enables filling below the liquid level.

•

These operating instructions do not

replace the company’s own standard

operating procedures (SOPs).

•

Wear appropriate protective clothing

when handling chemical substances.

•

Ensure that the fill heads are not used

after the maximum period of use has

expired. The duration of use depends

on the chemicals used.

•

Before using the products, check the

materials for their chemical resistance.

2.4 General safety instructions

•

Always observe the safety data sheets

(SDS) of the chemicals used.

•

Only use cleaned products. The prod-

ucts described in these operating

instructions have been cleaned in an

ultrasonic bath at the factory.

•

Only use products for which the chem-

ical resistance of the components is

guaranteed.

Safety

Содержание DH -N2 Series













































Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды

AS DH -N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды