AS DH -N2 Series Скачать руководство пользователя

Страница: 5 / 44

AS Strömungstechnik GmbH

www.asstroemungstechnik.de

Version date: 09/2020

1.3 Symbols and labels

The following symbols are used in these

operating instructions to depict hazards

and notes:

DANGER

Indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTE

Designates a situation that can result in

material damage.

1.4 Copyright protection

Despite all care taken, data and character-

istics can change – even at short notice.

We therefore do not assume any liability

or guarantee for the topicality, correctness

and completeness of the information.
Figures, graphics and texts as well as the

design of these operating instructions are

subject to copyright protection and other

protective laws. Duplication – also in ex-

cerpts – requires the prior written consent

of AS Strömungstechnik GmbH, if duplica-

tion is not legally permitted.

General information

1.5 Guarantee and warranty

AS Strömungstechnik GmbH assumes no

liability for errors or damage that occurred

due to improper handling of the products.
Improper handling is in particular in the

event of non-compliance with the operating

instructions, incorrect handling, negli-

gence, unauthorized replacement of parts

and other interventions.
The customer is responsible for testing the

chemical resistance of the fill heads and

their service life.
Fill heads and other products which have

come into contact with media/chemicals

(except ultra pure water) cannot be taken

back.
AS Strömungstechnik GmbH reserves the

right to make design changes due to fur-

ther development of AS products.
Our customer service is always available

even after the guarantee period has ex-

pired.

Содержание DH -N2 Series













































Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды

AS DH -N2 Series, Руководство по эксплуатации

Результаты поиска

Содержание DH -N2 Series

Отзывы:

Похожие инструкции для DH -N2 Series

Бренды по названию

Популярные бренды