ARTERY AT32F421 Series Скачать руководство пользователя страница 209 | Manualshive

Страница: 209 / 337

background image

AT32F421

Series Reference Manual

2022.11.11

Page 209

Rev 2.02

This bit indicates whether a recapture is detected when
C1IF=1. This bit is set by hardware, and cleared by
writing “0”.
0: No capture is detected
1: Capture is detected.

Bit 8: 2

Reserved

0x00

resd

Kept at its default value.

Bit 1

C1IF

0x0

rw0c

Channel 1 interrupt flag
If the channel 1 is configured as input mode:
This bit is set by hardware on a capture event. It is
cleared by software or read access to the TMRx_C1DT
0: No capture event occurs
1: Capture event is generated
If the channel 1 is configured as output mode:
This bit is set by hardware on a compare event. It is
cleared by software.
0: No compare event occurs
1: Compare event is generated

Bit 0

OVFIF

0x0

rw0c

Overflow interrupt flag
This  bit  is  set  by  hardware  on  an  overflow  event.  It  is
cleared by software.
0: No overflow event occurs
1:  Overflow  event  is  generated.  If  OVFEN=0  and
OVFS=0 in the TMR14_CTRL1 register:
− An overflow event is generated when OVFG= 1 in the
TMR14_SWEVE register;
−  An  overflow  event  is  generated  when  the  counter
CVAL is reinitialized by a trigger event.

14.3.4.4 Software event register (TMR14_SWEVT)

Bit

Register

Reset value

Type

Description

Bit 15: 2

Reserved

0x0000

resd

Kept at its default value.

Bit 1

C1SWTR

0x0

wo

Channel 1 event triggered by software
This bit is set by software to generate a channel 1 event.
0: No effect
1: Generate a channel 1 event.

Bit 0

OVFSWTR

0x0

wo

Overflow event triggered by software
This bit is set by software to generate an overflow event.
0: No effect
1: Generate an overflow event.

14.3.4.5 Channel mode register1 (TMR14_CM1)

The channel can be used in input (capture mode) or output (compare mode). The direction of a channel
is defined by the corresponding CxC bits. All the other bits of this register have different functions in
input and output modes. The CxOx describes its function in output mode when the channel is in output
mode, while the CxIx describes its function in output mode when the channel is in input mode. Attention
must be given to the fact that the same bit can have different functions in input mode and output mode.

Output compare mode:

Bit

Register

Reset value

Type

Description

Bit 15: 7

Reserved

0x000

resd

Kept at its default value.

Bit 6: 4

C1OCTRL

0x0

rw

Channel 1 output control
This field defines the behavior of the original signal
C1ORAW.
000: Disconnected. C1ORAW is disconnected from
C1OUT;
001: C1ORAW is high when
TMR14_CVAL=TMR14_C1DT
010: C1ORAW is low when
TMR14_CVAL=TMR14_C1DT
011: Switch C1ORAW level when
TMR14_CVAL=TMR14_C1DT
100: C1ORAW is forced low
101: C1ORAW is forced high.

«
...
207
208
209
210
211
...
»

Содержание AT32F421 Series


















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT32F421 Series

Бренд: VAF instruments Страницы: 56

Бренд: Jetter Страницы: 35

Бренд: A10 Страницы: 52

Бренд: Clavister Страницы: 89

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: Campbell Страницы: 38

ZyXEL ZyAIR B-120

Бренд: ZyXEL Communications Страницы: 20

Бренд: Moxa Technologies Страницы: 36

Бренд: Hauppauge Страницы: 55

Бренд: Aaeon Страницы: 57

Бренд: Juniper Страницы: 196

Бренд: Microcomputer Systems Страницы: 21

Бренд: Pilz Страницы: 12

Бренд: Kordis Страницы: 31

Бренд: Forcepoint Страницы: 2

Бренд: artisan Страницы: 36

Бренд: Tektronix Страницы: 143

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды