manualshive.com logo in svg

ARTERY AT32F421 Series, Справочное руководство, Страница: 254 / 337

Поделиться
Скачать
ARTERY AT32F421 Series Скачать руководство пользователя страница 254

  AT32F421

 

Series  Reference  Manual

 

2022.11.11

 

Page 254 

 

Rev 2.02

 

14.5.4.13 

TMR16 and TMR17 brake register (TMRx_BRK) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 16    Reserved 

0x0 

resd 

Kept at its default value. 

Bit 15 

OEN 

0x0 

rw 

Output enable 

This  bit  is  used  to  enable  the  output  of  CxOUT  and 
CxCOUT  for  those  channels  that  are  configured  as 
output. 

0: Output disabled 

1: Output enabled. 

Bit 14 

AOEN 

0x0 

rw 

Automatic output enable 
OEN is set automatically at an overflow event. 
0: Disabled 
1: Enabled 

Bit 13 

BRKV 

0x0 

rw 

Brake input validity 
This bit is used to select the active level of a brake input. 
0: Brake input is active low.   
1 Brake input is active high. 

Bit 12 

BRKEN 

0x0 

rw 

Brake enable 
This bit is used to enable brake input. 
0: Brake input is disabled. 
1: Brake input is enabled. 

Bit 11 

FCSOEN 

0x0 

rw 

Frozen channel status when holistic output enable 
This bit acts on the channels that have complementary 
output. It is used to set the channel state when the timer 
is inactive and MOEN=1. 
0: CxOUT/CxCOUT outputs are disabled. 
1: CxOUT/CxCOUT outputs are enabled. Output inactive 
level.   

Bit 10 

FCSODIS 

0x0 

rw 

Frozen channel status when holistic output disable 
This bit acts on the channels that have complementary 
output. It is used to set the channel state when the timer 
is inactive and MOEN=0. 
0: CxOUT/CxCOUT outputs are disabled. 
1: CxOUT/CxCOUT outputs are enabled. Output idle 
level. 

Bit 9: 8 

WPC 

0x0 

rw 

Write protection configuration 
This field is used to enable write protection. 
00: Write protection is OFF. 
01:  Write  protection  level  3,  and  the  following  bits  are 

write protected: 

TMRx_BRK: DTC, BRKEN, BRKV and AOEN 
TMRx_CTRL2: CxIOS and CxCIOS 
10: Write protection level 2. The following bits and all bits 

in level 3 are write protected: 

TMRx_CCTRL: CxP and CxCP 
TMRx_BRK: FCSODIS and FCSOEN 
11: Write protection level 1. The following bits and all bits 

in level 2 are write protected: 

TMRx_CMx: C2OCTRL and C2OBEN 
Note: Once WPC>0, its content remains frozen until the 
next system reset. 

Bit 7: 0 

DTC 

0x00 

rw 

Dead-time configuration 
This field defines the duration of the dead-time insertion. 
The  3-bit  MSB  of  DTC[7:  0]  is  used  for    function 
selection: 
0xx: DT = DTC [7: 0]    * TDTS   
10x: DT = (64+ DTC [5: 0]) * TDTS * 2 
110: DT = (32+ DTC [4: 0]) * TDTS * 8 
111: DT = (32+ DTC [4: 0]) * TDTS * 16 

Note: Based on lock configuration, AOEN, BRKV, BRKEN, FCSODIS, FCSOEN and DTC[7:0] can all 

be  write  protected.  Thus  it  is  necessary  to  configure  write  protection  when  writing  to  the 
TMRx_BRK register for the first time. 

Содержание AT32F421 Series


















































































































































































































































































































































Отзывы:

Нет отзывов