ARRI ARTEMIS 2 Скачать руководство пользователя страница 50

Страница: 50 / 93

Installation and Operation

Locking Clamp Lever

6. After the camera has reached the desired position, push the clamp lever all

the way to the right until the clamp mechanism is securely locked.

Camera Dovetail Plates

ADVICE

Using the SAM plates will speed up the camera setup and later the balancing process.

The special hight of every SAM plate will lift the dedicated camera right into the center of the

TRINITY 2 inner ring.

This way a perfect COG of the camera is guaranteed.

Available SAM plates and lens support brackets.

K2.0041201

Stabilizer Adapter Mount SAM-Zero

K2.0018851

Stabilizer Adapter Mount SAM-1 for ALEXA

K2.0014215

Stabilizer Adapter Mount SAM-2 for ALEXA

KK.0016116

Stabilizer Adapter Mount SAM-2 Set for ALEXA Mini

K2.0014630

Stabilizer Adapter Mount SAM-3 Set for AMIRA

K2.0024508

Stabilizer Adapter Mount SAM-6

K2.0039405

Stabilizer Adapter Mount SAM-6 450mm/18in

K2.0034512

CSS Broadcast Dovetail Plate (SAM plate standard width)

K2.0039803

Stabilizer Plate for CBP 355mm/14in

K2.0038536

Stabilizer Plate for CBP 450mm/18in

K2.0033662

Stabilizer Adapter Mount SAM-4

KK.0038971

Long Stabilizer Mount 15mm Mini/Mini

KK.0038972

Long Stabilizer Mount 19mm Mini/Mini LF

K2.0039089

Compact Lens Support CLS-1

K2.0040036

Balance Utility Dovetail BUD-2

K2.0039861

Dovetail Utility Base DUB-1

K2.0038537

Stabilizer System Bracket SSB-2 19mm

Содержание ARTEMIS 2






























































































Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Похожие инструкции для ARTEMIS 2

Бренды по названию

Популярные бренды

ARRI ARTEMIS 2, Руководство пользователя

Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Похожие инструкции для ARTEMIS 2

Бренды по названию

Популярные бренды