manualshive.com logo in svg

ARRI ARTEMIS 2, Руководство пользователя

Поделиться
Скачать
ARRI ARTEMIS 2 Скачать руководство пользователя страница 22

Safety Instructions

22

Warning Symbols and Product Labels

General warning sign

Warning of electrical voltage

Warning of hot surfaces

Warning of hand injuries

Warning of the risk of crushing

Warning of obstacles on the ground

Please read all instructions care-

fully before using the product for

the first time.

Direct Current symbol found on elec-

tronics requiring or producing DC

power

6.2

General Safety Instructions

WARNING

Operating the TRINITY 2 in case of obvious damage

Risk of electric shock and fire hazard caused by short circuit.

Do not use the system if electrical lines or housing are visibly damaged.
Operate the system using only the type of power source indicated in the manual.
Unplug the power cable by gripping the power plug, not the cable.
Do not operate the system in areas with humidity above operating levels or expose it to water or

moisture.

Do not get the system wet.
Do not lay cables over sharp edges (e.g. sheet metal, profile or other cut edges). Damaged

cables can cause electric shock, short circuit or fire.

Do not remove or deactivate any safety measures from the system (incl. warning stickers or paint

marked screws).

Repairs may only be carried out by authorized ARRI service partners.

WARNING

Falling TRINITY 2 components

If the TRINITY 2 components is inadequately built up or assembled, it can fall down and

cause serious injuries and damage to the camera accessories or property.

Installation and operation may only be carried out by trained personnel who are familiar with the

system. Observe accident prevention regulations.

Do not place the TRINITY 2 on an unstable trolley or hand truck, stand, tripod, bracket, table or

any other unstable support device.

Always place the TRINITY 2 on dedicated support devices.
Secure the TRINITY 2 against falling and tipping over. Observe the general and local safety

regulations.

Содержание ARTEMIS 2






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды