ARRI ARTEMIS 2 Скачать руководство пользователя страница 76

Страница: 76 / 93

Installation and Operation

Free Positioning of the Battery Mounts

The combination of the BHM, which is equipped with 19 mm rods, and the freely positionable battery

system allows the size and weight distribution of the counterweight in the lower slide to be designed in

an unprecedented way.

8.7.5 Connecting the Battery Mounts to the Battery Hanger Module

The battery mounts BMS-1 & BMS-2 are equipped with a LEMO90° elbow connectors.

In order to give you more flexibility when placing the battery mounts, the three Battery In sockets can be

rotated by 90° and the elbow plug can be placed in the required position.

Right side

BAT IN 1

and

BAT IN 3

can be brought into the desired

position by turning the sockets 90° around below.

ADVICE

not

turn the

Bat In

sockets

upside down

Only

turn the sockets around

underneath!

Содержание ARTEMIS 2






























































































Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Бренды по названию

Популярные бренды

ARRI ARTEMIS 2, Руководство пользователя

Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Бренды по названию

Популярные бренды