ARRI ARTEMIS 2 Скачать руководство пользователя страница 72

Страница: 72 / 93

Installation and Operation

4. Move the clamping lever to the 45 ° position.

→ The dovetail plate is already completely secured and can no

longer be removed upwards. On the other hand, the dovetail plate

can still be moved fore and aft in this position and thus the cam-

era's COG can be roughly positioned.

5. Move the clamping lever all the way to the right.

6. Press the clamping lever into the end position, to

finally block the dovetail plate.

→ The SAM dovetail plait is mounted.

Camera Dovetail Plates

ADVICE

Using the SAM plates will speed up the camera setup and later the balancing process.

The special hight of every SAM plate will lift the dedicated camera right into the center of the

TRINITY 2 inner ring.

This way a perfect COG of the camera is guaranteed.

Available SAM plates and lens support brackets.

K2.0041201

Stabilizer Adapter Mount SAM-Zero

K2.0018851

Stabilizer Adapter Mount SAM-1 for ALEXA

K2.0014215

Stabilizer Adapter Mount SAM-2 for ALEXA

KK.0016116

Stabilizer Adapter Mount SAM-2 Set for ALEXA Mini

K2.0014630

Stabilizer Adapter Mount SAM-3 Set for AMIRA

K2.0024508

Stabilizer Adapter Mount SAM-6

K2.0039405

Stabilizer Adapter Mount SAM-6 450mm/18in

K2.0034512

CSS Broadcast Dovetail Plate (SAM plate standard width)

K2.0039803

Stabilizer Plate for CBP 355mm/14in

K2.0038536

Stabilizer Plate for CBP 450mm/18in

K2.0033662

Stabilizer Adapter Mount SAM-4

Содержание ARTEMIS 2






























































































Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Похожие инструкции для ARTEMIS 2

Бренды по названию

Популярные бренды

ARRI ARTEMIS 2, Руководство пользователя

Результаты поиска

Содержание ARTEMIS 2

Отзывы:

Похожие инструкции для ARTEMIS 2

Бренды по названию

Популярные бренды