ARRI ARTEMIS 2 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 93

background image

Overview

46

What is it ?

The newly developed Battery Mounting System enables extremely flexible use and attachment

of different battery types (B-Mount, V-Mount & G-Mount) on the TRINITY generation 1 and 2 and

ARTEMIS generation 2.

How does it work?

The battery holder system consists of a base module with a the rod clamp mechanism to which three

different battery holders can be attached quickly and easily.
The newly developed clamping mechanism allows the BMS to be mounted on the 19 mm rods of

the new Battery Hanger Gen. 2 (BAH-2) as well as on the 18 mm rods of the of the first generation

TRINITY Battery Hanger.

What problems does it solve?

The new clamping mechanism allows the BMS to be attached directly to the desired position.
The cumbersome pushing of the mounts onto the rods is no longer necessary.

Which combinations are possible?

There are currently three different battery mounts available to be used with the Battery Hanger Modul

Gen. 2 / BHM-2:

V-Mount (12V), Gold Mount (12V) and B-Mount (24V).

There are two versions of the BMS:

BMS-2

with

4pin LEMO 2B

for the Battery Hanger Gen. 2

for Battery Hanger Modul Gen. 2

BHM-2

K2.0039300

BMS-1

with

3pin LEMO 1B

for the TRINITY

Battery Hanger Gen. 1 /

BHM-1

K2.0037707

The

BMS-2

can be combined with the:

B-Mount for BMS-2

K2.0040284

Gold Mount for BMS-1 / BMS-2

K2.0040285

V-Mount for BMS-1 / BMS-2

K2.0040286

The BMS-2 transmits status information of the batteries as soon as the batteries offer data

communication.

The

BMS-1

can be combined with the:

Gold Mount for BMS-1 / BMS-2

K2.0040285

V-Mount for BMS-1 / BMS-2

K2.0040286

The

BMS-1

does not transmit any status information of the batteries.

BMS-1 can

NOT

be used with the

B-Mount (24V)

battery mount.

«
...
44
45
46
47
48
...
»

Содержание ARTEMIS 2






























































































Отзывы:

Нет отзывов

Похожие инструкции для ARTEMIS 2

Бренд: Dancover Страницы: 31

Бренд: Manfrotto Страницы: 2

Бренд: La Crosse Technology Страницы: 6

Бренд: ZKTeco Страницы: 4

Бренд: Zircon Страницы: 2

Бренд: Zircon Страницы: 1

Бренд: Antec Страницы: 5

Бренд: Mahindra Страницы: 25

Бренд: Deka Страницы: 4

BIS M-411-068-001-09-S72

Бренд: Balluff Страницы: 2

INV 220V Series

Бренд: Sunny Страницы: 11

CV MY FIRST TRAMPOLINE AND ENCLOSURE

Бренд: Chad Valley Страницы: 15

Бренд: poly-planar Страницы: 2

Бренд: Naish Страницы: 23

FIX&GO automatic

Бренд: Alfa Romeo Страницы: 40

Бренд: FAAFTECH Страницы: 8

Бренд: AutoMaxi Страницы: 2

H-BLACK PRO DYNAMO

Бренд: HERRMANS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды