manualshive.com logo in svg

ARRI ARTEMIS 2, Руководство пользователя

Поделиться
Скачать
ARRI ARTEMIS 2 Скачать руководство пользователя страница 38

Overview

38

What does it do?

The RCP-3 is used to set up and control the TRINITY Gen 2 system.
Depending on the camera, lens and accessories used, parameters such as the power and torque of the

motors of the TRINITY must be set to the total payload of the camera setup.
The user can also program the general function, the speed and other parameters of the Master Grip

TRINITY joystick via the RCP-3 to suit their personal preferences.

How does it work?

The RCP-3 uses a newly developed user-friendly GUI (Graphical User Interface), which divides the

application of the TRINITY into three areas.

1 Setup of the PID values.

Setting the PID values, or in other words, the power and torque of the motors, as well as the

responsiveness of the entire control loop.

2 Adjustment of the joystick and other controllers to the needs of the user.

For example direction, as well as the speed, sensitivity and ramp of the joystick.

3 The RCP-3 can also be used to control the lens via the LBUS.

With the Master Grip TRINITY / MGT-2, the user can now control the tilt axis and zoom of the lens

simultaneously with just one hand.

Содержание ARTEMIS 2






























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды