Arredo Inox Maturmeat 100 Скачать руководство пользователя страница 6

Страница: 6 / 57

Rev 2, 18.06.19

1.5

RECEIPT INSPECTION

All Maturmeat® units are factory tested for performance and are free from defects when

shipped. The utmost care has been taken in crating this product to protect against damage in

transit.

You should carefully inspect your Maturmeat® unit for damage during delivery, even if the crate

is free from damage. If damage is detected, you should save all the crating materials and make

note on the carrier’s Bill Of Lading describing this. A freight claim should be filed immediately. If

damage is subsequently noted during or immediately after installation, contact the respective

carrier and file a freight claim. Under no condition may a damaged unit be returned without first

obtaining written permission (return authorization).

1.6

INSTALLATION

DANGER

Excessive Weight Hazard

Use two or more people to move

and install your Maturmeat®.

Failure to do so can result in back

or other injury.

LOCATION:

Select a proper location away from extreme heat or

cold. Space above the unit should allow for breath-

ability to the condensing unit and access to the Water/

Aroma tanks. Allow enough clearance between the

unit and the side wall in order to allow the doors to fully

open.

PACKAGING:

The unit is shipped from the factory strapped to a stur-

dy wooden pallet and protected by MDF crating. The

crating is attached to the pallet with nails and several

screws. These should first be removed to avoid scratch-

ing the unit when lifting off the crating. To remove the

Maturmeat® from the wooden pallet start by cutting

free the nylon bands. There are 4 bolts connecting the

Maturmeat® to the pallet, remove them to release the

Maturmeat® from the pallet.

Most exterior surfaces have a protective vinyl covering

to prevent scratching during manufacturing, shipping,

and installation, remove after installation and discard.
NOTE: DO NOT LAY THE UNIT ON ITS SIDE/BACK/FRONT

DURING TRANSPORTATION OR INSTALLATION.
POWER CORD:

An attached power cord is provided without plug,

shipped coiled inside the compressor compartment.

For your safety and protection, have the installer con-

nect the proper plug for your country by checking with

the information on the data plate. Connect only to an

appropriate dedicated 20 amp outlet.

DANGER

Electrical Hazard

Never connect power to unit

via extension cord or adapter,

this can cause damage to the

system and/or start a fire.

POWER SUPPLY:

The supply voltage should be checked prior to connec-

tion to be certain that proper voltage for the cabinet

wiring is available (refer to the data plate for the correct

unit voltage). Make connections in accordance with lo-

cal electrical codes. Use qualified electricians.

Use of a separate, dedicated circuit is required.

Size wiring to handle indicated load and provide neces-

sary overcurrent protector in circuit (see amp require-

ments on the unit’s data plate).

DANGER

Keep all packaging away from

children

Содержание Maturmeat 100


























































Результаты поиска

Содержание Maturmeat 100

Отзывы:

Похожие инструкции для Maturmeat 100

Бренды по названию

Популярные бренды

Arredo Inox Maturmeat 100, Руководство пользователя

Результаты поиска

Содержание Maturmeat 100

Отзывы:

Похожие инструкции для Maturmeat 100

Бренды по названию

Популярные бренды