manualshive.com logo in svg

ARIS TENSOR, Оригинальное учредительное заявление с ручным управлением

Поделиться
Скачать
ARIS TENSOR Скачать руководство пользователя страница 22

22

Tensor

Fault message

Errors in operation, the controller indicates by permanently flashing an error code. Details about the error codes see section 8.2. 

Motor movements

The controller displays motor position and direction. The motor position 
is displayed as a %-value from 0 to 100%. The current %-value calcula-
tes the regulator from the distance between the two end positions. The 
left end position is corresponding to the value of 100%, the right of 0%.

If the motor rotates, a circulating dash running around both segments 
indicates the direction of rotation. Direction of the dash movement 
shows the direction of rotation of the output shaft at sight through the drive. Indication of position and direction of rotation are 
displayed with the drive running and changing every second.

Sleep mode

If the regulator is not activated for 10 seconds, it goes into sleep mode and displays the %-value of the motor position every two 
seconds. The controller leaves the sleep mode as soon as a button is pressed or the motor is driven.

Before starting up the controller, the end positions must be programmed.

At Tensor M note reverse direction of rotation!

ADVICE

!

Содержание TENSOR

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды