manualshive.com logo in svg

ARIS TENSOR, Оригинальное учредительное заявление с ручным управлением

Поделиться
Скачать
ARIS TENSOR Скачать руководство пользователя страница 20

20

Tensor

Actual value output
The output (2) at pin 54/55 is supplying a voltage or current depen-
ding on the DIP switch setting. The output is galvanically isolated from 
the other ports.

Set value input
Via pin 51/52 the controller receives a set value. When connecting a 
potentiometer (1) pin 53 supplies the encoder with the supply voltage.
Via the DIP switches 3 and 4, the controller receives the information for 
use of input:
− Set value via poti (1)
− Set value as current (2)
− Set value as voltage (3)

6.2 

Configure controller connection

To operate a drive control, the DIP switches must be configured
and the ports on the controller I-ACT (PMR) connected.

Setting up DIP switches

Component damage by short-circuit.
The DIP switches 1-2 and 3-4 switch to the same outputs. Are the DIP switches 1 and 2 or 
the DIP switches 3 and 4 ON during operation, a short circuit can destroy components. 
− Do not set DIP 1 and 2 to ON at once  
− Do not set DIP 3 and 4 to ON at once

Via DIP 1-2 (1) the actual value output is configured. With DIP 3-4 (2) configure the setpoint input.

Cut off supply voltage, set up DIP switches:

DIP   Actual value

1 ON / 2 OFF 

0...10 V

1 OFF / 2 ON 

0...20 mA

DIP 1 and DIP 2 to OFF creates an undefined condition.

DIP   Set value input

3 ON / 4 OFF 

0...20 mA

3 OFF / 4 ON 

0...10 V

3 OFF / 4 OFF 

0...5 V / Poti operation

CAUTION

Содержание TENSOR

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды