manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 46

page 44

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290  •  docID: P10001

Key Switch

The Key switch is located on the right side of the

instrument panel. It has two positions: OFF and ON.

Insert the Key and turn it to the right to switch it to the ON

position. Turn the Key to the left to switch it OFF.

Key Switch- ON Position

Turn the Key to the ON position to turn the FUV ON: You

will hear the start-up chime and see the Display turn on.

When the FUV is turned ON, all electronic features are

available, but the motors are off. The FUV must be turned

ON in order to start.

To start, turn the Key to the ON position and press the

START button on the left grip (see page

46

). Note that the

Parking Brake must be fully depressed to start the FUV.

Refer to the

Getting Started section on page 35

for

details.

Once the FUV has been started, it will move in the
direction specified by the Direction switch (see page

48

)

when the throttle is twisted.

Always check the Direction switch before twisting the throttle.

Because the FUV is silent, it may not be obvious that the vehicle
has been started. Never leave the FUV unattended while it is
turned ON!

NOTE

You can also turn the FUV ON without a Key by using the 6-

digit PIN. (see page

84

).

CONTROLS

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды