ARCIMOTO FUV 2022 Скачать руководство пользователя страница 49

Страница: 49 / 194

CONTROLS

Headlights Switch

The bottom position is DAY MODE.

Note that for safety, the headlights are
always turned on when the Key is in the
ON position.

The center position is NIGHT MODE -
LOW BEAM:

Headlights are turned on, and the
Display is dimmed slightly for night
driving.

The Headlight telltale on the Display
is lit green.

The top position is NIGHT MODE -

HIGH BEAM:

High Beams are activated, and the
Display is dimmed slightly for night
driving.

The Headlight telltale on the Display
is lit blue.

Hazard Lights Button

Push the HAZARD LIGHTS button to
activate hazard lights (all turn signals
flashing). Push again to turn them off.

Horn Button

Press the HORN button to sound the
horn.

Turn Signal Switch

Slide the switch left or right to start
signaling. Push the center of the switch in
to turn off the signal.

NOTE

The Hazard Lights, Horn, and Turn signals can be activated
even if the FUV is completely powered OFF.

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • doc ID: P10001

page 47

Содержание FUV 2022



































































































































































































Результаты поиска

Содержание FUV 2022

Отзывы:

ARCIMOTO FUV 2022, Руководство пользователя, Страница: 49 / 194

Результаты поиска

Содержание FUV 2022

Отзывы: