manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 149

MAINTENANCE AND CLEANING

Wheel Removal and
Replacement

If a tire is flat, remove the wheel and take it to a qualified
tire technician for repair.

Do not attempt to change a tire on the side of the vehicle close
to moving traffic. Pull far enough off the road to avoid the
danger of being hit when operating the jack or changing the
wheel.

Being under an elevated vehicle is dangerous. The vehicle could
slip off the jack and fall on you. You could be crushed.

Never put any part of your body under a vehicle that is on a
jack. If you need to get under a raised vehicle, take it to a
service center where it can be raised on a lift.

Never start or run the FUV while it is elevated.

The vehicle should be jacked on a firm level surface only. Avoid
ice or slippery areas.

Note that it is necessary to elevate the FUV to remove the
wheel; refer to page

142

for details on safely elevating the

FUV.

Removing a Wheel

1. Remove the lug nuts (M12 x 1.50) with a lug wrench

turning them counterclockwise.

2. Slide the wheel off of the axle.

FUV Owner's Manual (REV 0)  • last revised: 3/31/2022 • part# 006290  •  doc ID: P10001

page 147

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды