ARCIMOTO FUV 2022 Скачать руководство пользователя страница 17

Страница: 17 / 194

SAFETY

Safety

Please read this manual carefully and completely before

operating this FUV. Do not attempt to operate this FUV

until you have attained adequate knowledge of its

controls and operating features, and until you have been

trained in safe and proper riding techniques.

Regular inspections and proper maintenance, along with

good riding skills, help you safely enjoy your FUV.

Disregarding the aforementioned, however, may render

the warranty invalid.

Failure to follow recommended precautions and procedures
could result in severe injury or death. Always heed all safety
precautions

and

all

operation,

inspection

and

maintenance procedures outlined in this Owner's Manual.

High Voltage Safety
Information

DANGER:

Exposure to high voltage can

cause shock, burns, and even death. The
high voltage components in the vehicle
can

only

serviced

Arcimoto

authorized

service

technicians.

High

voltage components are identified by
labels. Do not remove, open, take apart, or
modify these components.

High voltage cable or wiring has orange
covering or labels. Do not touch, probe,
tamper with, cut, or modify high voltage
cable or wiring.

This vehicle has two non-serviceable high voltage battery

modules, and a standard 12V battery.

If the FUV is in a crash, the sensing system may shut down

the high voltage system. When this occurs, the high

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • doc ID: P10001

page 15

Содержание FUV 2022



































































































































































































Результаты поиска

Содержание FUV 2022

Отзывы:

Бренды по названию

Популярные бренды

ARCIMOTO FUV 2022, Руководство пользователя

Результаты поиска

Содержание FUV 2022

Отзывы:

Бренды по названию

Популярные бренды