manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 143

MAINTENANCE AND CLEANING

To avoid leakage, never over-fill the washer fluid bottle. When
finished adding fluid, there should not be wiper fluid visible in
the Remote Fill Neck or the plastic tube that fills the bottle.

5. Replace and tighten the Remote Fill Neck cap.

6. Replace the Front Access Panel, and twist both

thumbscrews clockwise to secure the panel.

Seat Belts

To clean dirt or debris from the seat belts, sponge the
straps with mild soap and water.

Do not allow water, cleaners, or fabric to enter a seat belt
mechanism; failure of the retraction mechanism may result. If
you notice any damage on a seat belt, contact Arcimoto
Product Support at (541) 780-0032.

l

Do not use bleach, dye or household detergents.

l

Do not let wet seat belts dry in the sun. Move the
FUV to a shaded area until the belts are totally dry.

l

Make sure that seat belts are totally dry before
allowing them to retract.

Interior

Clean with warm water and a soft, clean cloth (flannel or
chamois). If necessary, use a small amount of liquid dish
washing soap.

l

Do not use bleach, dye, or household detergents.

l

Using solvents (including alcohol), bleach, citrus,
naphtha, or silicone-based products or additives on
interior components can cause damage.

l

Statically- charged materials can cause damage to
the Display and sensitive internal components.

FUV Owner's Manual (REV 0)  • last revised: 3/31/2022 • part# 006290  •  doc ID: P10001

page 141

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды