manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 152

page 150

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290  •  docID: P10001

Recreational Transport

Recreational vehicle transport refers to towing the FUV
behind another vehicle such as a motor home.

You cannot tow the FUV with any wheels on the ground
as vehicle or transmission damage will occur.

You must tow your FUV with all three wheels off the
ground, such as when using a flat-bed trailer.

Consider

the

following

important

points

before

transporting the FUV:

l

Before transporting the FUV, become familiar with
the local laws that apply to recreational vehicle
towing. These laws vary by region.

l

The towing capacity of the towing vehicle. Follow
the tow vehicle manufacturer's recommendations.

l

Whether the towing vehicle has the proper towing
equipment.

l

Whether the trailer has an approved load rating
greater than the actual weight of the FUV, including
any installed accessories or cargo.

l

Whether the FUV is ready to be transported. Ensure
that no loose items are inside the FUV, and remove
all cargo. Engage the Parking Brake, remove the
Key, and chock all wheels.

Contact Arcimoto Product Support at (541) 780-0032 for
advice and equipment recommendations.

Buckle Seat Belts During Transport

In high winds, or over a long distance, seat buckles can
whip around and damage the FUV. When transporting,
buckle all seat belts to avoid potential damage.

MAINTENANCE AND CLEANING

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды