manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 150

page 148

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290  •  docID: P10001

3. Slide the hub spacer off the axle.

4. Store the wheel, lug nuts, and spacer in a safe

location.

Replacing a Wheel

The correct lug nut torque for all three wheels on the FUV
is 80 ft- lbs (108.5 Nm). If in doubt about the correct
tightness, have the wheels checked with a torque wrench
by an Arcimoto Service Technician or at a service station.

NOTE

Use only Arcimoto- recommended lug bolts, and clean or
remove any dirt or oil before tightening. If you need assistance,
call Product Support at (541) 780-0032.

Proper torque is important to ensure that the wheel is properly
mounted to the vehicle. Any time a wheel has been removed
and reinstalled, the lug nuts should be torqued using a properly
calibrated torque wrench using a high quality deep wall socket.

1. Mount the hub spacer on the axle, with the flat side

of the spacer facing the brake rotor.

2. Mount the wheel on the axle.

3. Install the lug nuts with the cone shaped end of the

nut toward the wheel. Lightly tighten the lug nuts.

4. Lower the vehicle to the ground.

5. Finish tightening the lug nuts.

To avoid the risk of forcing the vehicle off the jack, do not
tighten the lug nuts fully until the vehicle has been lowered.
Failure to follow this warning may result in serious injury.

Tighten the lug nuts in a star
pattern until each nut has been
tightened twice.

Push down on the wrench while at
the end of the handle for
increased leverage.

MAINTENANCE AND CLEANING

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды