manualshive.com logo in svg

ARCIMOTO FUV 2022, Руководство пользователя

Поделиться
Скачать
ARCIMOTO FUV 2022 Скачать руководство пользователя страница 160

page 158

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290  •  docID: P10001

STEP 5: Flip the RESET Lever on the 12V Circuit

Breaker

On the 12V Circuit Breaker, flip the RESET lever up to the
closed (ON) position.

To verify that 12V power has been restored, touch the
Display; it should turn on.

If it does

not

turn on when touched:

l

Check the 12V Circuit Breaker to ensure that the
RESET lever is flipped fully up (in the ON position).

l

Check both Power Output Connectors to ensure
that they are fully connected. The locking tabs snap
into place when the connectors are fully seated.

STEP 6: Replace the Service Port Panels

Carefully replace both service port panels, and use a
Phillips-head screwdriver to hand-tighten the screws.

The hard reset is complete, and the FUV is ready to start.

Note

: If after following the steps above the issue is still

present, or if the 12V icon on the Display is illuminated

red

,

please call Arcimoto Product Support (541-780-0032) for
assistance.

Charging the 12V Battery

If the 12V Battery in the FUV loses its charge, the FUV may
not be able to start. In this case, it is necessary to re-
charge the 12V Battery.

This is easily done by connecting an external trickle
charger (not included) to the 12V Accessory Power
Socket located directly below the Control Panel.

Use this feature to charge a discharged 12V Battery, via an
external 12V trickle charger (not included).

MAINTENANCE AND CLEANING

Содержание FUV 2022



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды