ARCIMOTO FUV 2022 Скачать руководство пользователя страница 50

Страница: 50 / 194

page 48

FUV Owner's Manual (REV 0) • last revised: 3/31/2022 • part# 006290 • docID: P10001

Right Hand Controls

Direction Switch (

/•/

)

The

Direction

switch

sets

the

direction

travel

(Forward/Neutral/Reverse).

Always check the Direction switch before putting the FUV
into motion.

Slide the switch to the left (UP arrow) for

Forward

. The FUV will move forward when the

throttle is twisted.

The middle position is

Neutral

. The FUV will

not move when the throttle is twisted.

Slide the switch to the right (down arrow) for

Reverse

. The FUV will move backwards when

the throttle is twisted.

Switch the Direction switch from Neutral to Forward or
Reverse, and gently twist the throttle to start moving.

Always start the FUV with the Direction switch in
Neutral (•)

CONTROLS

Содержание FUV 2022



































































































































































































Результаты поиска

Содержание FUV 2022

Отзывы:

Бренды по названию

Популярные бренды

ARCIMOTO FUV 2022, Руководство пользователя

Результаты поиска

Содержание FUV 2022

Отзывы:

Бренды по названию

Популярные бренды