APRILIA DORSODURO 1200 ABS - ATC Скачать руководство пользователя страница 155

Страница: 155 / 408

•

If shorted to positive: disconnect the probe connector and check the sensor correct resist-

ance: replace the sensor if not OK; if it is OK, restore the cable harness (Green/Red cable)

•

If circuit is open, shorted to negative: check circuit continuity from probe connector (PIN 3

and 4) toward the probe: if it is not OK, replace the probe; if it is OK, check the sensor

connector and the Marelli control unit connector: if it is not OK, restore; if it is OK, with key

set to ON and sensor connector disconnected, check if there is battery voltage at PIN 4: if

it is not OK, check the Pink/Brown cable continuity between the probe connector and the

auxiliary injection relay (No. 35 in the wiring diagram, placed in the front relay box, left side;

CHECK, however, the identification of the relay with the colour of the cables). If there are

also coil, lower and upper injector and secondary air errors, check the relay and its excitation

and power line; if there is voltage at PIN 4, check the Green/Red cable ground insulation

(PIN 3): if not OK, restore the cable harness. If it is OK, check the continuity of the Green

cable (between the sensor connector PIN 3 and the ENGINE PIN 32) and restore the cable

harness.

•

If circuit is open, shorted to negative: check circuit continuity from probe connector (PIN 3

and 4) toward the probe: if it is not OK, replace the probe; if it is OK, check the sensor

connector and the Marelli control unit connector: if it is not OK, restore; if it is OK, with key

set to ON and sensor connector disconnected, check if there is battery voltage at PIN 4: if

it is not OK, check the Red/Brown cable continuity between the probe connector and the

auxiliary injection relay (No. 35 in the wiring diagram, placed in the front relay box, left side;

CHECK, however, the identification of the relay with the colour of the cables). If there are

also coil, lower and upper injector and secondary air errors, check the relay and its excitation

and power line; if there is voltage at PIN 4, check the Green/Red cable ground insulation

(PIN 3): if not OK, restore the cable harness. If it is OK, check the continuity of the Green/

Red cable (between the sensor connector PIN 3 and the ENGINE PIN 32) and restore the

cable harness.

WARNING

The control unit does not detects the following malfunctions of the lambda probe circuit according to

the signal: interrupted circuit, shorted to ground or sensor malfunction (for example non variable volt-

age). In case of fault indication, carry out the following troubleshooting.

Troubleshooting

•

Check circuit continuity from probe connector (PIN 1 and PIN 2) toward the probe: replace

the lambda probe if there is no continuity; if there is continuity, check the sensor connector

and the Marelli control unit connector: If not OK, restore. If OK, check continuity between

the ENGINE connector PIN 22 and PIN 10 and restore the cable harness.

DIAGNOSIS INSTRUMENT: LOGIC ERRORS

Lambda probe P0134

- voltage without variation.

Error cause

DORSODURO 1200 ABS - ATC

Electrical system

ELE SYS - 155

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды

APRILIA DORSODURO 1200 ABS - ATC, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды