APRILIA DORSODURO 1200 ABS - ATC Скачать руководство пользователя страница 278

Страница: 278 / 408

Inspecting the crankshaft components

Crankshaft axial clearance check

•

The shaft axial clearance on the crank-

case should be checked with a dial

gauge mounted on the specific dial

gauge support.

•

The clearance should be between 0.1

- 0.26 mm (0.0039 - 0.0102 in).

•

If the clearance is beyond tolerance,

check the reference surfaces.

Specific tooling

020714Y

Dial gauge mounting

Removal

•

Mark the position of the original semi-bushings on the crankcase.

•

To reduce the installation force neces-

sary, score an incision approximately

0.5 mm (0.02 in) deep (without cutting

into the steel shell) in each semi-bush-

ing in the area indicated in the figure.

•

Remove the bushings with the crank-

case cold, using a press and the spe-

cific tool and pushing inward from the

outside of the crankcase.

Specific tooling

020726Y

Extractor for bushings

Engine

DORSODURO 1200 ABS - ATC

ENG - 278

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды

APRILIA DORSODURO 1200 ABS - ATC, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды