APRILIA DORSODURO 1200 ABS - ATC Скачать руководство пользователя страница 144

Страница: 144 / 408

Intake pressure sensor

Figure key

•

A - Rear

•

B - Front

Function

The pressure sensors (one at the front, one at the

rear) are fundamental for calculation of generated

torque, for calculation of ambient pressure and for

correct ignition timing during start-up.

Operation / Operating principle

Diaphragm sensor which translates the diaphragm

position into electrical voltage when in contact with

the intake air.

Level in electrical circuit diagram:

Intake air pressure sensor

Location:

•

on the vehicle: rear cylinder sensor on

rear throttle body right side, front cylin-

der sensor on front throttle body left

side.

•

connector: on the sensor.

Electrical specifications: -

Pin out:

1. Power supply 5V

2. Ground connection

3. Output signal

DIAGNOSIS INSTRUMENT: PARAMETERS

Front Cylinder Intake Pressure

•

Example value with key ON: 1004 mbar

•

Example value with engine on: 715 mbar

•

NOTE: pressure read by the front sensor

Rear Cylinder Intake Pressure

•

Example value with key ON: 1003 mbar

•

Example value with engine on: 720 mbar

•

NOTE: pressure read by the rear sensor

Front Cylinder estimated Intake Pressure

Electrical system

DORSODURO 1200 ABS - ATC

ELE SYS - 144

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды

APRILIA DORSODURO 1200 ABS - ATC, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды