APRILIA DORSODURO 1200 ABS - ATC Скачать руководство пользователя страница 238

Страница: 238 / 408

•

Fit the clutch springs.

•

Fit the screw washers.

•

Tighten the six screws operating in

stages and diagonally.

•

On reassembly, replace the gasket under clutch cover.

Installing the clutch cover

CLUTCH-SIDE COVER OIL SEAL INSTALLATION

•

For controlled driving of the oil seal, take a 0.5 mm (0.020 in) thick washer, having an inside

diameter of 12 mm (0.47 in) and outside diameter of 20 mm (0.79 in).

•

Prepare the following tools:

Specific tooling

020376Y

Adapter handle

020362Y

12 mm guide

020891Y

Adapter 25 mm (0.98 in)

•

Assemble the tool using the washer for

controlled driving then, paying atten-

tion to the assembly direction, set the

oil seal in its seat, with marking facing

the operator.

•

Place the oil seal retainer with its flat

side resting against the oil seal.

Engine

DORSODURO 1200 ABS - ATC

ENG - 238

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Содержание DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды

APRILIA DORSODURO 1200 ABS - ATC, Руководство по обслуживанию станции

Результаты поиска

Содержание DORSODURO 1200 ABS - ATC

Отзывы:

Похожие инструкции для DORSODURO 1200 ABS - ATC

Бренды по названию

Популярные бренды