APRILIA 854239 Скачать руководство пользователя страница 98

Страница: 98 / 216

0.2 mm (0.0079 in)

Checking the clutch housing

The clutch bell for this vehicle can be identified by a line on the toothing outside diameter and it engages

with the engine pinion, the kick-start pedal gear and the lubrication gear.

Check the clutch bell for damage and wear that may result in clutch irregular operation. If necessary,

replace the bell.

Check the riveted joint between the clutch housing and the primary drive sprocket for correct sealing

and evenness.

Check the primary driven gear for damage and

wear and, if necessary, replace the primary driven

gear and the clutch bell all together.

Make sure there is not excessive noise during op-

eration; if necessary, replace the primary drive

gear and the clutch bell all together.

Checking the pusher plate

Check the thrust plate and the bearing for damage

and wear. If necessary, replace the parts.

Engine

MXV 450

ENG - 98

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды