APRILIA 854239 Скачать руководство пользователя страница 47

Страница: 47 / 216

4. Right coil

5. Right spark plug

6. Engine temperature sensor

7. Throttle position sensor (TPS)

8. Crankshaft revolution/timing sensor

9. Intake air temperature sensor

10.ECU

11.Left injector

12.Left coil

13.Left spark plug

14.Stepper motor

15.Voltage regulator

16.Condenser

Electrical system installation

Central part

The filter housing has been redesigned with the aim of centralising the ground connections and housing

delicate electrical components like:

•

Injection Ignition ECU

•

Stick-type coils

•

Condenser

•

Air temperature sensor

•

Voltage regulator (external)

•

Electrical wiring

For this reason, while fitting be careful with the possible interferences between the cable harness and

the moving parts such as throttle control cable and throttle body levers.

Throttle control cables are prefitted on the throttle

body.

Once the throttle body has been removed from the

filter housing, link the main cable harness to the

Stepper motor, to the throttle valve sensor, to the

right injector, to the capacitor and to the intake air

temperature sensor.

MXV 450

Electrical system

ELE SYS - 47

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды