APRILIA 854239 Скачать руководство пользователя страница 104

Страница: 104 / 216

•

Remove the head cover.

•

Remove the camshaft gear and re-

move the timing chain properly.

•

Remove the fix slider.

•

Undo and remove the head fixing

screw on the timing system side.

NOTE

THE CAMSHAFT FIXING SCREW OF THE FRONT CYLIN-
DER WORKS ANTICLOCKWISE; THE FIXING SCREW OF
THE REAR CYLINDER, CLOCKWISE.

NOTE

REMOVE THIS SCREW BEFORE REMOVING THE FOUR
MAIN SCREWS.

•

Undo and remove the four head fixing

screws using a roundhead universal

socket wrench if required.

•

Remove the head and collect the head

gasket and the centring bushings.

Cylinder head

Removing the decompression system

•

Remove the rockers.

•

Lock the camshaft with the 6 mm (0.24

in) pin used for timing.

•

Undo and remove the fixing screw of

the decompressor control lock.

Engine

MXV 450

ENG - 104

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды